Hello everybody.
I have a doubt.
I need to create an AccessPoint on the ESP8266.
I am using the following test code.
Hard resetting via RTS pin...
New upload port: COM3 (serial)
�$N|G�h�d�lCO���h`��KI:R�AppStart
WORKS
Access Point IP: 192.168.4.1
[/QUOTE]
The log suggests that everything is ok, but I don't see the WiFi network created on nearby devices.
When I try to search for the WiFi network, nothing appears.
I tried running similar code directly in the Arduino IDE and it worked.
see how the code turned out.
this code works ok.
I tried to do the same with c inline in b4r but it didn't work either.
what could be wrong in b4r code?
I attached an image, which shows that the board and door are correct. They are the same on both the Arduino IDE and the B4R.
Note: I'm using the latest version of b4r, cli and java 14.0.1
thxx
I have a doubt.
I need to create an AccessPoint on the ESP8266.
I am using the following test code.
B4X:
Private Sub AppStart
Serial1.Initialize(9600)
Log("AppStart")
If wifi.StartAccessPoint2("DOUGLASTESTE", "123456789") Then
Log("WORKS")
Log("Access Point IP: ", wifi.AccessPointIp)
End If
Here is the log
[QUOTE]
End SubNew upload port: COM3 (serial)
�$N|G�h�d�lCO���h`��KI:R�AppStart
WORKS
Access Point IP: 192.168.4.1
[/QUOTE]
The log suggests that everything is ok, but I don't see the WiFi network created on nearby devices.
When I try to search for the WiFi network, nothing appears.
I tried running similar code directly in the Arduino IDE and it worked.
see how the code turned out.
C++:
#include <ESP8266WiFi.h>
// Defina o nome e a senha da sua rede WiFi
const char *ssid = "NomeDaSuaRede";
const char *password = "SuaSenha";
void setup() {
Serial.begin(9600);
// Configurar o modo WiFi do ESP8266 como AP (Ponto de Acesso)
WiFi.mode(WIFI_AP);
// Configurar o SSID e a senha do WiFi
WiFi.softAP(ssid, password);
Serial.println("Ponto de Acesso Iniciado!");
Serial.print("IP Address: ");
Serial.println(WiFi.softAPIP());
}
void loop() {
// Nada a fazer aqui, o AP está rodando
}this code works ok.
I tried to do the same with c inline in b4r but it didn't work either.
B4X:
Sub Process_Globals
Public Serial1 As Serial
Private wifi As ESP8266WiFi
Private ssid As String = "DOUGLASTESTE" 'ignore
Private password As String = "123456789" 'ignore
End Sub
Private Sub AppStart
Serial1.Initialize(9600)
Log("AppStart")
RunNative("SetAP", Null)
RunNative("setSoftAP", Null)
Log("Access Point IP: ", wifi.AccessPointIp)
Log(wifi.LocalIp)
End Sub
#if C
void SetAP(B4R::Object* o) {
WiFi.mode(WIFI_AP); // Configurar o modo WiFi para AP (Ponto de Acesso)
}
#end if
#if C
void setSoftAP(B4R::Object* o) {
WiFi.softAP(b4r_main::_ssid->data, b4r_main::_password->data);
}
#end ifwhat could be wrong in b4r code?
I attached an image, which shows that the board and door are correct. They are the same on both the Arduino IDE and the B4R.
Note: I'm using the latest version of b4r, cli and java 14.0.1
thxx